Change or rekey · Toronto
Smart Lock Installation
You have just taken possession of the house and the previous owners handed over a keypad deadbolt with a code nobody wrote down and an app account you cannot get into. It needs to become yours, properly, or be replaced.
Smart Lock Installation
In plain words
Most of the skill in fitting a smart lock goes into the door rather than the electronics. Motors are patient but not strong, so a bolt that has to be shouldered home will stall, chew through batteries and eventually refuse. The locksmith checks that the bolt slides fully into the strike with the door closed and no hand on it, and corrects hinges, strike pocket or weatherstrip until it does. The bore holes are measured against the new lock's needs, the door's thickness is confirmed, and a reinforced strike goes in with long screws. Only then is the lock mounted, calibrated and programmed.
How the visit goesYour mother still lives on her own, and the personal support worker, the pharmacy delivery and two siblings all need to get in on different days. Cutting keys for everyone feels wrong; a code for each person, with a log, feels right.
Toronto
How the visit goes
Measuring the door and its holes
Smart locks are built around the standard residential preparation, so the locksmith measures before choosing. Door thickness is usually between 35 and 45 millimetres; thicker doors need an extension kit and very thin ones may need a different model. The large cross bore for the cylinder, the smaller edge bore for the bolt and the backset from the door edge to the centre of the hole are each checked against the new lock's range. A lever set also needs the handing confirmed. Steel and fibreglass doors, doors with a mortise pocket from an older lock, and doors with glass close to the handle each change what will fit and how it is mounted.
Fitting the bolt, the body and the strike
With the door ready, the mechanical parts go in first. The new bolt is set to the door's backset and slid into the edge bore with its face plate flush. The outside assembly, keypad or touch surface, is placed with its cable fed through the cross bore, and the inside mounting plate is fixed so the two halves clamp the door without twisting. Screws are driven by hand rather than with an impact driver, because an over-tightened housing binds the motor. The interior unit is seated on the plate and the tailpiece aligned so the thumb-turn and the motor share the same travel. A reinforced strike with long screws replaces the light original.
Batteries, warnings and the cold months
A smart lock runs on batteries, and you leave knowing how that side of it behaves. The locksmith shows where the low-battery warning appears on the lock and in the app, how to swap the set, and which type to buy so the motor gets steady power. Cold shortens battery life, so a fresh set before the first hard frost is a sensible habit, and the alert should go to a phone someone actually reads. If the model has an external emergency power contact, you will have seen it used and know where a nine-volt battery lives for the day it is needed.
Smart Lock Installation
In the van
- Mechanical override cylinder and repinning kit
- Reinforced box strike with long screws
- Hinge shims and long hinge screws
- Hand screwdrivers, Phillips and Torx
- Door-position sensor magnet
What affects the quote
Same fees day, night or weekend
1Storm door and weather adjustments
Where the entrance calls for a vented storm door panel, a keypad shield or a model rated for heat and cold exposure, those items are named separately so you can choose them or not.
2Pairing a smart deadbolt with a smart lever on the same door
Some doors get a smart deadbolt only, while others pair it with a smart lever below so both turn from one app and share the same codes. Fitting and programming two devices on one door takes more work than one, confirmed once the door and hardware are seen.
3Travel and access to the property
Distance to the address and how easy the door is to reach, such as a condo with a locked lobby or a rural property at the end of a long drive, are part of any call-out.
Smart Lock Installation: questions
Fingerprint, fob, code or phone: which is worth having?
It depends on who uses the door. Codes suit everyone and need nothing in hand. Fobs or cards are a favourite for children and for anyone who finds small buttons difficult, since a tap does it. Fingerprint readers are convenient for a household of adults but can be fussy with cold, wet or gloved hands in winter, so pair them with a code. Phone control is for whoever wants alerts and remote checks. Most families end up using two of these.
Can I install a smart lock myself?
Many people do, and on a door that already closes perfectly with the standard holes the instructions are manageable. Where a locksmith earns their place is everything around the box: recognizing a bolt that drags before it wears out a motor, enlarging or filling holes cleanly, fitting a reinforced strike, rekeying the override so the old key retires, and setting up the account and codes in a way that is easy to manage later. If you have started and hit a snag, that is a normal call too.
I rent. Can I have a smart lock installed?
Yes, with your landlord's agreement first. Tenancy rules in this province expect a tenant to have the landlord's consent before changing a lock, and expect the landlord to have a working way in, so the sensible route is a short conversation and a note of what will be fitted. A retrofit model that mounts inside and keeps the existing exterior lock and key is often the easiest thing for a landlord to say yes to, since the door is unchanged from outside.
Change or Rekey Locks
Smart Lock Installation near you
Residents and business owners in Toronto can use this list to find the service that fits, then read what it involves before anyone comes out. Emergency openings are here. So are rekeys, lock changes, deadbolt and high-security upgrades, commercial door hardware, master keys, safes and key cutting.